Welcome to
|
Doctor Ben's Super Sticky Adhesive (All Scales)
#2924
Have you ever thought how nice it would be to be
able to glue paper or cardstock product to a non-porous
material such as metal, plastic or even wood and doesn’t
leave lumpy-globs under that show through after the two
are stuck together?
You know the routine, you finally find
something that with stick to metal or plastic, but it
saturates or ruins the paper product. Or, how nice would
it be to simply glue two pieces of scribed siding to
make a double surface wall without the wood warping all
over the place? Can you glue a nice thin, rustic wood
laminate to the inside floor of that plastic boxcar so
that it is all beat up and really looks like the real
railroad?
Well we are here to tell you that all
your dreams are answered with this one single product,
Doctor Ben’s Super Sticky Adhesive. Yep, this stuff is
so sticky, that you may have a tough time getting things
back apart if you apply as we suggest. That is the down
side of this great product. The up side is that this
adhesive is made of the very same glue that is used to
apply used car decals (you know, the decals that you see
on the back of cars that nearly require an air chisel to
remove them). Use Doctor Ben’s Super Sticky Adhesive to:
glue metal to plastic; glue wood to wood; cardstock to
plaster casting; scale people to scenery (cannot be
loose) and so much more. I have used this product to
apply my signature “ribbed copper standing seam roofs
for years, & I have yet to have a roof to come off—even
setting out in the sun! How about applying Campbell’s
shingles without wetting them with water & never have
another warped roof! |
|
Instructions:
Before applying the Doctor Ben’s Super Sticky
Adhesive, dust or sand smooth any protruding or
loose particles that may leave unwanted “bumps”
protruding” from the material that you are
applying. And if you feel that one or both of
the surfaces may be too porous or powder, you
should consider some sort of primer or an old
paint color that you will never use again, but
try to use a lighter color especially if it will
be possible to see the color through the
material. I would recommend the Doctor Ben’s
Aged Driftwood. This product already has polymer
binder that enable it to stick to most surfaces
and it dries really fast, too!
Then, if you have those little alcohol
wipes, wipe the area clean. If you don’t have
these wipes, use a lint-free material with a
cleaner such as rubbing alcohol and allow the
surfaces to dry. If you just can’t wait, you can
hurry things along with a hair dryer.
Un-roll the Doctor Ben’s Super Sticky Adhesive
measuring out how much you need for a single
application across the surface of your material
and then cut enough strips to cover the material
fro bottom to top. It doesn’t hurt to let Super
Sticky Adhesive hang over the edge a 1/16” or
so. You will cut this off later.
Apply the one of the pieces that you’ve
cut for this project and with the sticky side
down on the surface of your material, burnish
the adhesive down using the protective waxed
paper. When you begin to apply the second, third
or more strips you do NOT need to overlap. All
that is necessary is to rest the second strip of
Super Sticky Adhesive up against the first piece
and continue the same until you have the area
covered that you are working with. Then peel off
the protective paper and start gluing. If you
peel of the protective wax paper after each
strip is applied, you may lose the reference
line of where the previous strip ended and
unintentionally overlap the adhesive. The only
concern about overlapping is wasting the Super
Sticky Adhesive. Overlapping the adhesive will
not show through the material that you are
gluing together.
If you make a mistake and the material
that you are applying is very thin, try to strip
it off and reapply the Doctor Ben’s Super Sticky
Adhesive. If you are trying to glue something
that is thicker, you can try using a heat gun to
soften the adhesive and you can use a lacquer
thinner if the lacquer thinner will not ruin
your parts. Please respond to the provided
address with critiques and techniques that you
have found useful while modeling with this
product and have fun!
Doctor Ben's Products are:
User
friendly,
No complex processes,
Color
fast—does not fade!
Super concentrated,
Clear, re-sealable containers,
Price Value $$$,
It's Doctor Ben's.
|
|
Each purchase is accompanied with a detailed full-page set of colored
instructions. |
|
Products
Developed Directly from the Creations of NMRA National Award
Winning Dioramas by Richard E. (Ben) Bendever
Doctor
Ben's Ready-To-Use Realistic Rust Weathering Solution
#1050
$6.49 +
S&H (8 ounce container!)
We are always
looking forward to hearing original ideas & feedback from our
friends & customers who have enjoyed using our products. Got a
story to share, or am image that you are especially proud of?
Send them in, we have thought that we should have more User
photos. As always we are happy to return your requested material
to you.
 |
